Zurich Instruments HF2LI는 DC와 50MHz 사이의 주파수 범위를 포괄하는 디지털 락인앰플리파이어(잠금증폭기)입니다. 자이로 스코프(gyroscopes)와 같은 MEMS 장치의 특성화 및 미세 유체(microfluidics) 영역의 측정을 위해 선택되는 기기(장비)입니다. HF2LI에는 Zurich Instruments 제어 소프트웨어 LabOne 이 장착되어 있습니다. 랩원(LabOne)은 특히 스펙트럼 분석기, 스위퍼 및 기본 오실로스코프 등을 특징으로하는 웹 기반 사용자 인터페이스를 제공합니다 . 다양한 업그레이드 옵션으로 HF2LI의 기능을 확장하여 다양한 애플리케이션에 적용 할 수 있습니다. 또한 HF2LI와 HF2TA 전류 증폭기를 결합하면 전류 입력이 가능합니다.
주요특징
- DC - 50 MHz, 210 MSa/s
- 2개의 독립 락인 유닛, 2개의 신호발생기
- 락인 유닛 당 1개의 기본주파수 및 2개의 고조파 분석 가능
- 4 개의 보조 출력, 2 개의 보조 입력
- USB 2.0, 480 Mbit/s
- LabOne® 도구 세트 : 오실로스코프, 스위퍼 및 스펙트럼 분석기를 포함
- 센싱 및 엑츄에이션 : MEMS 자이로스코프, 가속도계
- 미세 유체
- 비선형 이미징 : CARS, SRS, 테라헤르츠(terahertz) 이미징 등
- 레이저 분광법 (레이저 스펙트로스코피)
- 원자력 현미경 (AFM), 스캐닝 프로브 현미경 (SPM)
- 비파괴 검사
- 의료 기술
MDS (다중 장치 동기화)를 사용하면, 여러 HF2LI를 단일 다중 채널 장치로 작동 할 수 있습니다.
- 단일 LabOne 사용자 인터페이스 및 LabOne API에서 모든 기기를 작동합니다.
- 모든 계측기 클록과 발진기를 위상으로 고정합니다 (안정적인 위상 관계).
- 측정 데이터의 자동 정렬을 위해 타임 스탬프와 샘플링 속도를 동기화합니다.
여기에서 MDS에 대해 자세히 알아보십시오.
고정밀 입력
HF2LI의 2 개 입력 경로는 매우 낮은 노이즈 작동에 최적화되어 있습니다. 210 MSa/s의 샘플링 속도는 아날로그 대역폭의 4 배로 신호를 완벽하게 캡처하고 앨리어싱을 줄입니다.
신호 출력
HF2LI는 DC ~ 50 MHz 범위에서 최대 6 개의 정현파의 선형 조합으로 2 개의 고주파 출력을 생성합니다. HF2LI-MF 다중 주파수 옵션을 사용하여 각 주파수 성분에 대해 진폭, 주파수 및 위상시프트를 설정할 수 있습니다.
복조기 및 필터
HF2LI는 6 개의 이중 위상 복조기(6 dual-phase demodulators)를 제공합니다. 각 복조기는 시간 상수 (1 μs ~ 500 초, 80 μHz ~ 200 kHz의 신호 대역폭에 해당) 및 필터 차수 (1 ~ 8 차)를 포함한 자체 필터 속성으로 구성 할 수 있습니다. 필터는 128 비트 디지털 아키텍처로 구현됩니다. 기존 아날로그 장비에 비해 장점은 더 높은 다이나믹리저브, 제로 드리프트, 정확한 위상 편이 및 직교성입니다.
통합 도구(기능) 세트
2048개 샘플을 위한 메모리가 있는 통합 오실로스코프는, 입력 신호의 직접 신호 대 시간 및 스펙트럼 보기를 제공합니다. 입력 및 생성된 신호에 대한 개요보기를 언제든지 사용할 수 있으므로, 올바른 설정을 빠르게 찾을 수 있습니다. 주파수 응답 분석기는 정확한 신호 대 주파수 플롯을 제공합니다. FFT 스펙트럼 분석기는 장비에서 복조 된 신호에 대한 고해상도 스펙트럼보기를 제공합니다.
락인 작동 모드
Internal reference mode | Single and dual lock-in |
External reference mode | Single and dual lock-in |
Auto reference mode | Single and dual lock-in |
Dual-harmonic mode | 1 fundamental + 2 harmonics (simultaneous) |
Multi-harmonic mode | 1 fundamental + 5 harmonics (simultaneous), with HF2LI-MF |
Arbitrary frequency mode | 6 frequencies, with HF2LI-MF |
HF 아날로그 입력
Frequency range | DC - 50 MHz |
Input impedance | 50 Ω or 1 MΩ || 20 pF |
Input noise voltage | 5 nV/√Hz (above 10 kHz) |
Dynamic reserve | 120 dB |
Input range | ±3.3 V |
Input AC range | ±1.5 V (with DC coupling) |
Input full range sensitivity | 1 nV to 1.5 V |
A/D conversion | 14 bits, 210 MSa/s |
HF 아날로그 출력
Frequency range | DC - 50 MHz |
Output ranges | ±10 mV, ±100 mV, ±1 V, ±10 V |
Signal adder | ±10 V, DC to 50 MHz bandwidth |
D/A conversion | 16 bits, 210 MSa/s |
복조기 및 참조
Number of demodulators | 6 dual-phase |
Output sample rate | On USB: up to 460 kSa/s On auxiliary outputs: 1 MSa/s |
Filter time constant | 1 µs - 500 s |
Filter bandwidth | 80 µHz - 220 kHz |
Filter slope | 6, 12, 18, 24, 30, 36, 42, 48 dB/Oct |
X, Y, R, Theta | 64-bit full range |
Reference frequency resolution | 0.7 µHz |
Reference phase angle resolution | 1.0 µ° |
오실로스코프
Input channels | Signal inputs, signal outputs |
Scope modes | Time domain, frequency domain (FFT) |
Number of display channels | 1 |
Trigger channels | Signal inputs, signal outputs, oscillator phases, DIOs |
Trigger modes | Edge |
Sampling rates | 6.4 kSa/s to 210 Msa/s |
Vertical resolution | 14 bits |
Maximum number of samples per shot | 2048 |
Bandwidth limit mode, vertical resolution increase | Sample decimation, averaging |
Cursor math | Location, area, wave, peak, tracking, histogram |
스펙트럼 분석기
Center frequency range | 0 - 50 MHz |
Spectrum modes | FFT(X+iY), FFT(R), FFT(Θ), FFT(f) and FFT((dΘ/dt)/2π) |
Statistical options | Amplitude, spectral density, power |
Averaging modes | None, exponential moving average |
Maximum number of samples per spectrum | 8.4 MSa |
Maximum span | 460 kHz |
Window functions | Rectangular, Hann, Hamming, Blackman Harris |
Cursor math | Location, area, wave, peak, tracking, histogram |
스위퍼(Sweeper)
Scan parameters | Oscillator frequency, demodulator phase shift, auxiliary offset, signal output amplitudes, etc. |
Parameter sweep ranges | Full range, linear, logarithmic |
Parameter sweep resolution | Arbitrary, defined by start/stop value, number of sweep points |
Display parameters | Demodulator output (X, Y, R, Θ, f), auxiliary input |
Display options | Single plot, dual plot (e.g., Bode plot), multi-trace |
Statistical options | Amplitude, spectral density, power |
Preset measurement modes | Parameter sweep, noise amplitude measurement, frequency response analyzer, 3-omega-sweep |
보조 신호
High-speed outputs | 4 channels, ±10 V, amplitude, phase, frequency, X/Y, or user-defined |
D/A converter | 16 bits, 1 MSa/s |
D/A analog bandwidth | 200 kHz |
High-speed inputs | 2 channels, ±10 V |
A/D converter | 16 bits, 400 kSa/s |
A/D analog bandwidth | 100 kHz |
기타 인터페이스
Host connection | USB 2.0, 480 Mbit/s |
Pre-amplifier control bus | ZCtrl proprietary bus to control external pre-amplifiers |
Synchronization bus | ZSync proprietary bus to locally interconnect ZI instruments |
Digital I/O | 32 bits, general purpose |
일반
Dimensions | 45 x 35 x 10 cm (19" rack) |
Weight | 6.2 kg |
Power supply | 110-120 V, 220-240 V, 50/60 Hz |
Operating temperature | +5 °C to +40 °C |
Operating environment | IEC61010, indoor location, installation category II, pollution degree 2 |
Operating altitude | Up to 2000 m |
Internal oscillator output | Sine, ±1 V, 10 MHz |
Internal oscillator initial accuracy | ±1.5 ppm |
Internal oscillator temperature coefficient | 0.05 ppm/C |
Blog Posts
A deep dive into data acquisition with the DAQ tool
on 25.11.2019 by Moritz Kirste
DFRT revisited: from feedback optimization to full DAQ acquisition
on 18.02.2020 by Romain Stomp
Sensor characterization and control
on 25.05.2020 by Kivanç Esat
Square wave and sawtooth wave generation with the HF2LI Lock-in Amplifier
on 13.12.2013 by James Wei
Operate the HF2LI dual-channel lock-in amplifier with one reference frequency
on 24.05.2013 by James Wei
Optimize your HF2TA transimpedance amplifier settings
on 24.05.2013 by James Wei